put schematic output in a separate repository

Hardware/pdf/BSPD_ESF_Submit.tex

@@ -1,105 +0,0 @@
-\documentclass[paper=A4]{article}
-\usepackage[utf8]{inputenc}
-
-\usepackage[a4paper, left=2cm, right=2cm, top=2cm, bottom=2cm]{geometry}
-\usepackage{tikz}
-
-\usetikzlibrary{}
-\usetikzlibrary{calc,shapes.geometric, arrows}
-\usepackage[european, rotatelabels]{circuitikz}
-
-\usepackage{siunitx}
-\sisetup{
-     group-separator = {.},
-     input-decimal-markers={.}, 
-     output-decimal-marker = {,},
-     group-minimum-digits=4}
-\usepackage{graphicx}
-\usepackage{fancyhdr}
-\usepackage{lastpage}
-\usepackage{subfigure}
-\usepackage{float}
-\usepackage{multicol}
-\usepackage{amsmath, amssymb}
-
-\pagestyle{fancy}
-\fancyhf{}
-
-\rhead{\includegraphics*[scale=0.03]{bilder/Fasttube-Logo.png}}
-
-\rfoot{Page \thepage \hspace{1pt} of \pageref{LastPage}}
-
-% Circuitikz settings:
-\ctikzset{bipole annotation style/.style={color=black}}
-\ctikzset{bipole label style/.style={color=black}}
-
-% \tikzset{
-%   block/.style = {rectangle, draw, text centered, minimum height=2em},
-%   sensor/.style = {rectangle, draw, thick, blue, line width=2pt, text centered, minimum height=2em},
-%   arrow/.style = {thick,->,>=stealth}
-% }
-
-\begin{document}
-\lhead{\large Car 313, 06.03.2025, Rev. 1}
-\chead{\large BSPD Schematic}
-
-\begin{figure}[H]
-	\centering
-	\includegraphics[width=\textwidth]{./bilder/output.pdf}
-	\caption{Schematic of BSPD}
-\end{figure}
-
-The BSPD PCB is located in the front "Sensor-Node" (mainly there to transfer the analog data to CAN), in which a separate compartment is created to ensure the BSPD can be separated sealed without affecting other parts in the same housing.
-
-\begin{multicols}{2}
-	\textbf{Test Procedure}
-	\begin{enumerate}
-		\item apply external test current to the simulation coil
-		\item brake hard (with brake pressure $\geq 30 \unit{\bar}$)
-	\end{enumerate}
-	
-	\textbf{Test Current Calculation}
-	\begin{align*}
-		I_{test} & = 5 \unit{kW} / V_{max} = 5 \unit{kW} / 403.2 \unit{V} \\
-		         & = 12.401 \unit{A}
-	\end{align*}
-	\quad \quad 12 windings $\longrightarrow$ test current $\approx 1.034 \unit{A}$
-\end{multicols}
-
-\begin{figure}[H]
-	\centering
-	\begin{tikzpicture}[node distance=1cm]
-		% % Nodes
-		% \node (current) [block] {Current source};
-		% \node (sensor) [sensor, right of=current, xshift=3cm] {Lem HO-100s sensor};
-		% \node (bpressure) [block, below of=sensor, yshift=-2cm] {Brake Pressure Sensor};
-		% \node (bspd) [block, right of=sensor, xshift=4cm, yshift=-1cm] {BSPD PCB};
-		% \node (lvms) [circle, draw, above of=bspd, yshift=2cm] {+12V LVMS};
-		%
-		% % Connections
-		% \draw [arrow] (current.east) -- (sensor.west);
-		% \draw [arrow] (sensor.east) -- ++(2, 0) node[midway, above] {sen\_1} -- (bspd.west);
-		% \draw [arrow] (bpressure.east) -- ++(5, 0) node[midway, above] {sen\_2} -- (bspd.west);
-		% \draw [arrow] (lvms.south) -- (bspd.north);
-		% \draw [arrow] (bspd.east) -- ++(1, 0) node[midway, above] {SDC\_OUT};
-		% \draw [arrow] (bspd.west) ++(0, -0.5) -- ++(-1, 0) node[midway, above] {SDC\_IN};
-		%
-		% % Ground symbol
-		% \node (ground) [below of=bspd, yshift=-1cm] {};
-		% \draw (bspd.south) -- (ground) node[midway, right] {};
-		\draw[black, rounded corners, thick] (0,4) rectangle (3,6) node[midway]{Current source};
-		\draw[blue, rounded corners=24pt, line width=16pt] (5,4) rectangle (8,6) node[midway]{LEM HO-50S};
-		\draw[black, rounded corners, thick] (5,0) rectangle (8,2) node[midway, text width=2.5cm]{Brake Pressure Sensor};
-		\draw[black, rounded corners, thick] (12,2) rectangle (15,4) node[midway]{BSPD PCB};
-		\draw[->, rounded corners, ultra thick] (8.3,5) -- (10,5) -- (10,3.5) -- (12,3.5);
-		\draw[->, rounded corners, ultra thick] (8,1) -- (10,1) -- (10,2.5) -- (12,2.5);
-		\draw[rounded corners, very thick] (3,5.6) -- (5.6,5.6) -- (4.6,5.2) -- (5.4,5.2) -- (4.6,4.8) -- (5.4,4.8) -- (4.6,4.4) -- (3,4.4);
-		\draw[->, ultra thick] (13.5,5) -- (13.5,4);
-		\draw[->, ultra thick] (13.5,2) -- (13.5,1);
-		\draw(13.5,5.5) node[align=left]{SDC in};
-		\draw(13.5,0.5) node[align=left]{SDC out};
-	\end{tikzpicture}
-	\caption{current simulation schematic}
-\end{figure}
-
-\end{document}