Core/Src/status_led.c

@@ -13,8 +13,7 @@
 #define STATUS_LED_2_GREEN_PIN GPIO_PIN_14
 #define STATUS_LED_2_BLUE_PIN GPIO_PIN_15
 
-//TODO: change to correct values for the board
-#error "GPIO pins for status LEDs are not set correctly"
+#warning "GPIO pins for status LEDs are not set correctly"
 
 typedef struct {
     uint8_t red : 1;

STM32-for-VSCode.config.yaml

@@ -40,7 +40,7 @@ cxxDefinitionsFile:
 asDefinitionsFile:
 
 # Compiler flags
-cFlags: [-Wall, -Wextra, -Wno-unused-parameter]
+cFlags: []
 cxxFlags: []
 assemblyFlags: []
 linkerFlags:

STM32Make.make

@@ -43,7 +43,6 @@ Core/Src/main.c \
 Core/Src/shunt_monitoring.c \
 Core/Src/slave_monitoring.c \
 Core/Src/soc_estimation.c \
-Core/Src/status_led.c \
 Core/Src/stm32f3xx_hal_msp.c \
 Core/Src/stm32f3xx_it.c \
 Core/Src/system_stm32f3xx.c \
@@ -87,7 +86,7 @@ PREFIX = arm-none-eabi-
 POSTFIX = "
 # The gcc compiler bin path can be either defined in make command via GCC_PATH variable (> make GCC_PATH=xxx)
 # either it can be added to the PATH environment variable.
-GCC_PATH="/home/kbracher/.vscode-server/data/User/globalStorage/bmd.stm32-for-vscode/@xpack-dev-tools/arm-none-eabi-gcc/12.3.1-1.2.1/.content/bin
+GCC_PATH="/home/jasper/.config/Code/User/globalStorage/bmd.stm32-for-vscode/@xpack-dev-tools/arm-none-eabi-gcc/11.3.1-1.1.2/.content/bin
 ifdef GCC_PATH
 CXX = $(GCC_PATH)/$(PREFIX)g++$(POSTFIX)
 CC = $(GCC_PATH)/$(PREFIX)gcc$(POSTFIX)
@@ -163,7 +162,7 @@ CXXFLAGS += -g -gdwarf -ggdb
 endif
 
 # Add additional flags
-CFLAGS += -Wall -Wextra -Wno-unused-parameter 
+CFLAGS += 
 ASFLAGS += 
 CXXFLAGS += 
 
@@ -243,13 +242,13 @@ $(BUILD_DIR):
 # flash
 #######################################
 flash: $(BUILD_DIR)/$(TARGET).elf
-	"/home/kbracher/.vscode-server/data/User/globalStorage/bmd.stm32-for-vscode/@xpack-dev-tools/openocd/0.12.0-2.1/.content/bin/openocd" -f ./openocd.cfg -c "program $(BUILD_DIR)/$(TARGET).elf verify reset exit"
+	"/home/jasper/.config/Code/User/globalStorage/bmd.stm32-for-vscode/@xpack-dev-tools/openocd/0.11.0-5.1/.content/bin/openocd" -f ./openocd.cfg -c "program $(BUILD_DIR)/$(TARGET).elf verify reset exit"
 
 #######################################
 # erase
 #######################################
 erase: $(BUILD_DIR)/$(TARGET).elf
-	"/home/kbracher/.vscode-server/data/User/globalStorage/bmd.stm32-for-vscode/@xpack-dev-tools/openocd/0.12.0-2.1/.content/bin/openocd" -f ./openocd.cfg -c "init; reset halt; stm32f3x mass_erase 0; exit"
+	"/home/jasper/.config/Code/User/globalStorage/bmd.stm32-for-vscode/@xpack-dev-tools/openocd/0.11.0-5.1/.content/bin/openocd" -f ./openocd.cfg -c "init; reset halt; stm32f3x mass_erase 0; exit"
 
 #######################################
 # clean up