And also don't assert that there are no buffers queued up when handling
an EOS event. The pad's streaming thread might've already received a new
stream-start event and queued up a buffer in the meantime.
This still leaves a race condition where the srcpad task sees all pads
in EOS state and finishes the stream, while shortly afterwards a pad
might receive a stream-start event again, but this doesn't seem to be
solveable with the current aggregator design.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2769>
Otherwise setting the srcpad caps based on the sinkpad caps event will
already push a segment event downstream before the upstream segment is
known.
If the upstream segments are just forwarded when the upstream segment
event arrives this would result in two segment events being sent
downstream, of which the first one will usually be simply wrong.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2372>
When the GAP event was flagged with MISSING_DATA, subclasses
may want to adopt a different behaviour, for example by repeating
the last buffer.
As we turn these gap events into gap buffers, we need to flag
those, we do so with a new custom meta.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/708>
Meson generates a gdbinit file that will automatically load gstreamer
script. However that script uses a helper python module that needs
PYTHONPATH to be pointing into the right location in the source
tree to be able to find gst_gdb.py.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1796>
GLib guarantees libintl is always present, using proxy-libintl as
last resort. There is no need to mock gettex API any more.
This fix static build on Windows because G_INTL_STATIC_COMPILATION must
be defined before including libintl.h, and glib does it for us as part
as including glib.h.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2028>
It doesn't matter for measurement purposes whether receiving them takes
a while and various PTP servers are not prioritizing to send them,
causing them to be dropped unnecessarily and preventing proper
synchronization with such servers.
This is especially a problem if the RTTs in the network are very low
compared to the additional delay imposed by the server.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2161>
They are part of gst_dep already and we have to make sure to always have
gst_dep. The order in dependencies matters, because it is also the order
in which Meson will set -I args. We want gstreamer's config.h to take
precedence over glib's private config.h when it's a subproject.
While at it, remove useless fallback args for gmodule/gio dependencies,
only gstreamer core needs it.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2031>
Scenario:
- Source 1 requesting and waiting a clock id
- Source 2 requesting and waiting on a clock id
- Test attempting to crank both sources in the same GstHarness
gst_test_clock_crank() originally dropped locks between the retrieving
of the next clock id and advancing to the next clock id. This would
mean that both sources would race each other attempting to complete
their clock waits. Sometimes the operations would be performed in the
correct order, other times they would not and a FALSE return value would
be produced.
This would lead to an assertion in gst_harness_push_from_src() expecting
that all clock cranks to succeed.
Fix by ensuring that the clock wait produced is dealt with before
processing the next by not dropping the relevant locks after retrieving
the next clock id.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1299>
There's no need to do this, and it can make seeking far less accurate.
For a specific use case: I am working with a long (45-minute) MPEG-1 layer 3 file, which has a constant bit rate but no seeking tables. Trying to seek the pipeline immediately after pausing it, without the ACCURATE flag, to a location 41 minutes in, yields a location that is potentially over ten seconds ahead of where it should be. This patch improves that drastically.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/374>
Those will cause us to renegotiate at the next aggregate cycle,
and while at that point we may decide to reconfigure upstream
branches (in practice we don't as this is inherently racy,
and that's the reason why mixer subclasses perform conversion
internally), we certainly don't want to just forward the event
willy-nilly to all our sinkpads.
An actual issue this is fixing is when caps downstream of a
compositor are changed at every samples-selected signal emission,
for the purpose of interpolating the output geometry, and the
compositor has a non-zero latency, the reconfigure events were
forwarded to basesrc, which triggered an allocation query, which
in turn caused aggregator to have to drain (thus not being able
to queue <latency> frames), leading to disastrous effects
(choppy output as compositor couldn't consume frames fast enough,
the higher the latency the choppier the output)
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1464>
When detecting the remote time has been reset which may occur if remote
device providing the clock server has been power reset, then clock is
no longer synced. Setting clock state will trigger a signal to client
informing on sync lost making it possibility to take appropriate action.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/975>
gst_base_parse_reset() does not reset data_bytecount to 0, so
gst_base_parse_update_bitrates() uses a wrong value to calculate
the average bitrate on subsequent pipeline starts. This leads to an
excessive amount of "tag" events being pushed. These events include
very high "bitrate" values that diminish over time, and are produced
until the average bitrate is back to sane values.
Fixes#840
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1228>
An inactive pad is a pad which, in live mode, hasn't yet received
a first buffer, but has been waited on at least once.
Exposing API to support this behaviour allows users of aggregator
subclasses to request pads, and not start pushing data on those
immediately, while avoiding systematic timeouts.
Subclasses must check in explicitly to this behavior, most likely
by exposing a user-facing property, and must check whether a pad
needs ignoring when aggregating. That is because by design,
aggregator subclasses don't get a list of "ready" pads, but instead
directly iterate element->sinkpads.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/867>
Introduces a `libraries` variable that contains all libraries in a
list with the following format:
``` meson
libraries = [
[pkg_name, {
'lib': library_object
'gir': [ {full gir definition in a dict } ]
],
....
]
```
It therefore refactors the way we build the gir so that we can reuse the
same information to build them against 'gstreamer-full' in gst-build
when linking statically
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1093>
